Editing MAC-10
Jump to navigation
Jump to search
Warning: You are not logged in. Your IP address will be publicly visible if you make any edits. If you log in or create an account, your edits will be attributed to your username, along with other benefits.
The edit can be undone.
Please check the comparison below to verify that this is what you want to do, and then save the changes below to finish undoing the edit.
| Latest revision | Your text | ||
| Line 13: | Line 13: | ||
| weaponinfo = | | weaponinfo = | ||
| − | The MAC-10 (Military Armament Corporation Model 10, officially the M-10) is a compact, blowback operated machine pistol developed by Gordon B. Ingram in 1964. It is chambered in either .45 ACP | + | The MAC-10 (Military Armament Corporation Model 10, officially the M-10) is a compact, blowback operated machine pistol developed by Gordon B. Ingram in 1964. It is chambered in either .45 ACP or 9mm. A two-stage suppressor by Sionics was designed for the MAC-10, which not only abated the noise created, but made it easier to control on full automatic (although it also made the gun far less compact and concealable)<ref name = "ingram wiki">[[wikipedia:MAC-10|Wikipedia entry on MAC-10]]</ref>. |
The MAC-10 was designed to fill the role of a compact, cheap-to-produce submachine gun/personal defense weapon. To this end, the MAC-10 is built predominately of sheet steel stampings. A notched cocking handle protrudes from the top of the receiver, and turning the handle 90° locks the bolt, and acts as an indicator the weapon is unable to fire. The M10 has a telescoping bolt, which wraps around the rear face of the barrel. This allows a more compact weapon and balances the weight of the weapon over the pistol grip, where the magazine is located. The M10 fires from an open bolt, and the light weight of the bolt results in a rapid rate of fire. In addition, this design incorporates a built in feed ramp as part of the trigger guard (a new concept at the time) and to save on cost the magazine was recycled from the M3 Grease Gun. The barrel is threaded to accept a suppressor, which works by reducing the discharge's sound without attempting to reduce the speed of the bullet. This works well with the .45 ACP versions, as most loads are subsonic already, as opposed to special, low-powered subsonic loads usually required for suppressed 9mm weapons. At the suggestion of the United States Army, the suppressor also acts as a foregrip to inhibit muzzle rise when fired. Ingram added a small bracket with a small strap beneath the muzzle to aid in controlling recoil during fully automatic fire. | The MAC-10 was designed to fill the role of a compact, cheap-to-produce submachine gun/personal defense weapon. To this end, the MAC-10 is built predominately of sheet steel stampings. A notched cocking handle protrudes from the top of the receiver, and turning the handle 90° locks the bolt, and acts as an indicator the weapon is unable to fire. The M10 has a telescoping bolt, which wraps around the rear face of the barrel. This allows a more compact weapon and balances the weight of the weapon over the pistol grip, where the magazine is located. The M10 fires from an open bolt, and the light weight of the bolt results in a rapid rate of fire. In addition, this design incorporates a built in feed ramp as part of the trigger guard (a new concept at the time) and to save on cost the magazine was recycled from the M3 Grease Gun. The barrel is threaded to accept a suppressor, which works by reducing the discharge's sound without attempting to reduce the speed of the bullet. This works well with the .45 ACP versions, as most loads are subsonic already, as opposed to special, low-powered subsonic loads usually required for suppressed 9mm weapons. At the suggestion of the United States Army, the suppressor also acts as a foregrip to inhibit muzzle rise when fired. Ingram added a small bracket with a small strap beneath the muzzle to aid in controlling recoil during fully automatic fire. | ||
